 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| October 2004 U CT PROD ENT OLETE REPLACEM r at O BS e nt e D ED MMEN al Support C om/tsc RE C O .c ic NO echn ww.intersil t o ur T contac TERSIL or w IN 1-888- (R) HA-2602/883 Wideband, High Impedance Operational Amplifier Description The HA-2602/883 is an internally compensated bipolar operational amplifier that features very high input impedance coupled with wideband AC performance. The high resistance of the input stage is complemented by low offset voltage (5mV max at +25oC) and low bias and offset current (25nA max at +25oC) to facilitate accurate signal processing. Offset voltage can be reduced further by means of an external nulling potentiometer. The 4V/s minimum slew rate at +25oC and the minimum open loop gain of 80kV/V at +25oC enables the HA-2602/883 to perform high gain amplification of fast, wideband signals. These dynamic characteristics, coupled with fast settling times, make these amplifiers ideally suited to pulse amplification designs as well as high frequency or video applications. The frequency response of the amplifier can be tailored to exact design requirements by means of an external bandwidth control capacitor. Other high performance designs such as high gain, low distortion audio amplifiers, high-Q and wideband active filters and high speed comparators, are excellent uses of this part. Features * This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. * High Input Impedance . . . . . . . . . . . . . . . . . 40M (Min) 500M (Typ) * High Slew Rate . . . . . . . . . . . . . . . . . . . . . . . .4V/s (Min) 7V/s (Typ) * Low Input Bias Current . . . . . . . . . . . . . . . . 25nA (Max) 1nA (Typ) * Low Input Offset Current. . . . . . . . . . . . . . . . 5mV (Max) * Wide Unity Gain Bandwidth . . . . . . . . . . . 12MHz (Typ) * Output Short Circuit Protection Applications * Video Amplifier * Pulse Amplifier * High-Q Active Filters * High Speed Comparators * Low Distortion Oscillators Part Number Information PART NUMBER HA2-2602/883 TEMPERATURE RANGE -55oC to +125oC PACKAGE 8 Pin Can Pinout HA-2602/883 (METAL CAN) TOP VIEW COMP 8 BAL 1 + 3 4 V5 7 V+ -IN 2 6 OUT +IN BAL CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2002, 2004. All Rights Reserved Spec Number 1 511005-883 FN3700.2 HA-2602/883 Absolute Maximum Ratings Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 40V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to VPeak Output Current . . . . . . . . . . . . . . .Full Short Circuit Protection Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V Lead Temperature (Soldering 10s). . . . . . . . . . . . . . . . . . . . +300oC Thermal Information JC Thermal Resistance JA Metal Can Package . . . . . . . . . . . . . . . . . 160oC/W 75oC/W Package Power Dissipation Limit at +75oC for TJ +175oC Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625mW Package Power Dissipation Derating Factor Above +75oC Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3mW/oC CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Operating Conditions Operating Temperature Range. . . . . . . . . . . . . . . . -55oC to +125oC Operating Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V VINCM 1/2 (V+ - V-) RL 2k TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = 15V, RSOURCE = 100, RLOAD = 500k, VOUT = 0V, Unless Otherwise Specified. GROUP A SUBGROUPS 1 2, 3 +IB VCM = 0V, +RS = 100k, -RS = 100 1 2, 3 -IB VCM = 0V, +RS = 100, -RS = 100k 1 2, 3 Input Offset Current Common Mode Range IIO VCM = 0V, +RS = 100k, -RS = 100k 1 2, 3 +CMR V+ = +4V, V- = -26V 1 2, 3 -CMR V+ = +26V, V- = -4V 1 2, 3 Large Signal Voltage Gain +AVOL VOUT = 0V and +10V, RL = 2k 4 5, 6 -AVOL VOUT = 0V and -10V, RL = 2k 4 5, 6 Common Mode Rejection Ratio +CMRR VCM = +10V, V+ = +5V, V- = -25V, VOUT = -10V VCM = -10V, V+ = +25V, V- = -5V, VOUT = +10V RL = 2k 1 2, 3 1 2, 3 4 5, 6 -VOUT RL = 2k 4 5, 6 HA-2602/883 TEMPERATURE +25 C +125oC, -55oC o PARAMETERS Input Offset Voltage Input Bias Current SYMBOL VIO VCM = 0V CONDITIONS MIN -5 -7 -25 MAX 5 7 25 60 25 60 25 60 -11 -11 -10 -10 UNITS mV mV nA nA nA nA nA nA V V V V kV/V kV/V kV/V kV/V dB dB dB dB V V V V +25oC +125 C, -55 C +25oC +125oC, -55oC o o -60 -25 -60 -25 -60 11 +25 C +125oC, -55oC o +25oC +125 C, -55 C +25oC +125oC, -55oC o o 11 80 60 80 +25 C +125oC, -55oC o +25 C +125 C, -55 C +25 +125o oC o o o o 60 74 74 74 74 10 C, -55 C o -CMRR +25 C +125 oC, -55oC Output Voltage Swing +VOUT +25 C +125 C, -55 C +25oC +125o C, -55 C o o o o 10 - Spec Number 2 511005-883 HA-2602/883 TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: VSUPPLY = 15V, RSOURCE = 100, RLOAD = 500k, VOUT = 0V, Unless Otherwise Specified. GROUP A SUBGROUPS 4 5, 6 -IOUT VOUT = +10V 4 5, 6 Quiescent Power Supply Current +ICC VOUT = 0V, IOUT = 0mA 1 2, 3 -ICC VOUT = 0V, IOUT = 0mA 1 2, 3 Power Supply Rejection Ratio +PSRR VSUP = 5V, V+ = +10V, V- = -15V, V+ = +20V, V- = -15V VSUP = 5V, V+ = +15V, V- = -10V, V+ = +15V, V- = -20V Note 1 1 2, 3 1 2, 3 1 2, 3 -VIOAdj Note 1 1 2, 3 NOTE: 1. Offset adjustment range is [VIO (Measured) 1mV] minimum referred to output. This test is for functionality only to assure adjustment through 0V. HA-2602/883 TEMPERATURE +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC MIN 10 7.5 -3.7 -4.0 74 74 74 74 VIO-1 VIO-1 VIO+1 VIO+1 MAX -10 -7.5 3.7 4.0 UNITS mA mA mA mA mA mA mA mA dB dB dB dB mV mV mV mV PARAMETERS Output Current SYMBOL +IOUT CONDITIONS VOUT = -10V -PSRR Offset Voltage Adjustment +VIOAdj TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = 15V, RSOURCE = 50, RLOAD = 2k, CLOAD = 50pF, AVCL = +1V/V, Unless Otherwise Specified. GROUP A SUBGROUPS 7 8A, 8B -SR VOUT = +5V to -5V 7 8A, 8B Rise and Fall Time TR VOUT = 0 to +200mV, 10% TR 90% 7 8A, 8B TF VOUT = 0 to -200mV, 10% TF 90% 7 8A, 8B HA-2602/883 TEMPERATURE +25oC +125o C, -55 C o o PARAMETERS Slew Rate SYMBOL +SR CONDITIONS VOUT = -5V to +5V MIN 4 3 4 3 - MAX 60 70 60 70 UNITS V/s V/s V/s V/s ns ns ns ns +25 C +125oC, -55oC +25 C +125 C, -55 C +25oC +125o C, -55 C o o o o - Spec Number 3 511005-883 HA-2602/883 TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = 15V, RSOURCE = 50, RLOAD = 2k, CLOAD = 50pF, AVCL = +1V/V, Unless Otherwise Specified. GROUP A SUBGROUPS 7 8A, 8B -OS VOUT = 0 to -200mV 7 8A, 8B HA-2602/883 TEMPERATURE +25oC +125oC, -55oC +25oC +125oC, -55oC MIN MAX 40 50 40 50 UNITS % % % % PARAMETERS Overshoot SYMBOL +OS CONDITIONS VOUT = 0 to +200mV TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS Device Characterized at: VSUPPLY = 15V, RLOAD = 2k, CLOAD = 50pF, Unless Otherwise Specified. HA-2602/883 PARAMETERS Differential Input Resistance Full Power Bandwidth Minimum Closed Loop Stable Gain Output Short Circuit Current SYMBOL RIN FPBW CLSG +ISC VCM = 0V VPEAK = 10V RL = 2k, CL = 50pF VOUT = 1V, RL = 10 CONDITIONS NOTES 1 1, 2 1 1 1 1 -ISC VOUT = -1V, RL = 10 1 1 1 Quiescent Power Consumption NOTES: 1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization based upon data from multiple production runs which reflect lot to lot and within lot variation. 2. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2VPEAK). 3. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.) TABLE 4. ELECTRICAL TEST REQUIREMENTS MIL-STD-883 TEST REQUIREMENTS Interim Electrical Parameters (Pre Burn-In) Final Electrical Test Parameters Group A Test Requirements Groups C and D Endpoints NOTE: 1. PDA applies to Subgroup 1 only. SUBGROUPS (SEE TABLES 1 AND 2) 1 1 (Note 1), 2, 3, 4, 5, 6, 7, 8A, 8B 1, 2, 3, 4, 5, 6, 7, 8A, 8B 1 PC VOUT = 0V, IOUT = 0mA 1, 3 TEMPERATURE +25 C +25oC -55oC to +125oC +25oC +125oC -55oC +25oC +125oC -55oC -55oC to +125oC o MIN 40 50 1 -50 -45 -60 - MAX 50 45 60 120 UNITS M kHz V/V mA mA mA mA mA mA mW Spec Number 4 511005-883 HA-2602/883 Die Characteristics DIE DIMENSIONS: 69 x 56 x 19 mils 1 mils 1750 x 1420 x 483m 25.4m METALLIZATION: Type: Al, 1% Cu Thickness: 16kA 2kA GLASSIVATION: Type: Nitride (Si3N4) over Silox (SiO2, 5% Phos.) Silox Thickness: 12kA 2kA Nitride Thickness: 3.5kA 1.5kA WORST CASE CURRENT DENSITY: 3.9 x 104A/cm2 SUBSTRATE POTENTIAL (Powered Up): Unbiased TRANSISTOR COUNT: HA-2602/883: 140 Metallization Mask Layout HA-2602/883 +IN -IN BAL V- COMP BAL V+ OUT All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com Spec Number 5 511005-883 |
Price & Availability of HA2-2602883
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |